Home » Product documentation » MobilTherm-2-IP67

MobilTherm-2-IP67

Downloadable technical data sheet

Click the button below to download the datasheet
Download

Specifications

Module Operation

Panel structure

Based on the connection points, the MobilTherm-2-IP67 GSM temperature alarm consists of the following parts:

Top: microUSB connector

Side: Li-Po battery connector

Inside:

  • Battery jumper
  • Test button
  • nanoSIM card slot
  • Built-in antenna

Bottom:

  • Relay 2 terminal block
  • Relay 1 terminal block
  • Contact input 1
  • Contact input 2
  • Digital temperature sensor connectors
  • 230V mains power input


Installation recommendations and protection:

The panel is housed in an IP67-rated impact-resistant ABS plastic enclosure, providing maximum protection against dust, water, and mechanical impact. Cables can be routed through the 5 cable glands located at the bottom of the enclosure.

Warning:

  • If any terminal block is not wired out, the corresponding cable gland must be carefully sealed with a rubber, plastic, or metal plate to protect against water and moisture.
  • Improper sealing can compromise the panel's IP67 rating and lead to malfunctions.
Gomb felirata

Module commissioning

LED indicator meanings and functions

The LEDs on the MobilTherm-2-IP67 panel serve to indicate the device's status and various functions. The LEDs are red, green, yellow, or multi-colored, and indicate the current status of the device as follows:

In-1 (Yellow): Indicates the status of input 1. If the LED is continuously lit, input 1 is active (when a potential-free contact is applied).

In-2 (Yellow): Indicates the status of input 2. If the LED is continuously lit, input 2 is active (when a potential-free contact is applied).

Out-1 (Green): Indicates the status of high-current relay output 1. If the LED is continuously lit, relay 1 is energized.

Out-2 (Green): Indicates the status of high-current relay output 2. If the LED is continuously lit, relay 2 is energized.

T1 (Red/Green): Indicates the status of thermometer module 1.

  • Green (continuous): The temperature measured by thermometer 1 is within the set limits.
  • Red (continuous): The temperature measured by thermometer 1 is outside the set limits.
  • Red (flashing): Thermometer 1 is not connected or the connection is lost.

T2 (Red/Green): Indicates the status of thermometer module 2.

  • Green (continuous): The temperature measured by thermometer 2 is within the set limits.
  • Red (continuous): The temperature measured by thermometer 2 is outside the set limits.
  • Red (flashing): Thermometer 2 is not connected or the connection is lost.

Power (Red): Indicates the power supply. If the red LED flashes, the power supply is very low (below 11Vdc) or there is no power supply.

Status (Yellow/Green/Red): Used to indicate the GSM module and signal strength.

  • Yellow (continuous): Lights up for the first 10 seconds after power-on while the GSM module initializes and searches for a network.
  • Yellow (flashing): During GSM communication or USB mode (download, upload).
  • Green (flashing): Signal strength indication:
    1 flash: Weak signal, the device should be relocated.
    2 flashes: Weak signal, the module may restart, causing 30 seconds of downtime.
    3 flashes: Medium signal, the module operates stably.
    4 flashes: Strong signal, the module operates stably.
    5 flashes: Maximum signal strength.

Important warning:

If the Status LED flashes red and rapidly, check:

  • The correct connection of the GSM antenna.
  • The compatibility and PIN code status of the SIM card.

Programming module

Programming the Module with SMS

The MobilTherm-2-IP67 module can also be programmed remotely using SMS. The table below lists the most common memory locations, their functions, and their factory default contents. Commands must be entered precisely for the module to execute the desired action.

Memory Locations and SMS Commands:

Memory ID. Function Factory Default User Content
001 SMS center number +36309888000
002 Max. number of SMS sent in 2 hours 20
003 Module arming SMS command Elesites
004 Module disarming SMS command Tiltas
005 Automatic test time 72:00:00
010 Phone number 1 (master) +36301234567
011 Phone number 2
012 Phone number 3
013 Phone number 4
020 Name of thermometer 1 Living room
022 Thermometer 1 low alarm 16
026 Thermometer 1 notifications for signals S1,V1
030 Name of thermometer 2 Kitchen
031 Thermometer 2 high alarm 28
032 Thermometer 2 low alarm 18
033 Thermometer 2 notifications for signals S1,V1
038 Probe error message Probe error
039 Probe OK error message Probe OK
040 Name of input 1 Alarm
041 Input 1 when activated sounded
042 Input 1 when deactivated silenced
>043 Input 1 notifications for signals S1,V1
050 Power supply error name Power supply
051 Power supply error occurred error
052 Power supply error resolved OK
053 Power supply error notifications S1,V1
060 Name of input 2 Water level indicator
061 Input 2 when activated high level
062 Input 2 when deactivated normal level
063 Input 2 notifications for signals S1,V1
070 Name of output 1 Boiler
071 Output 1 activate command on
072 Output 1 deactivate command off
073 Output 1 relay timing 00:15:00
080 Name of output 2 Boiler
081 Output 2 activate command turn on
082 Output 2 deactivate command turn off
083 Output 2 relay timing 01:00:00
090 Service notifications for signals R1,V1,S1
091 Acknowledged events H1,J1,A1,B1,T
098 Thermometer offset +0.0,+0.0 Not editable!
500 Module type MobilTherm-2-xC Not editable!
501 Software version 1.14 Not editable!
502 Signal strength status message 0 Not editable!
503 Provider name ? Not editable!
504 Thermometer-1 0 Not editable!
505 Thermometer-2 0 Not editable!
506 Input-1 0 Not editable!
507 Input-2 0 Not editable!
508 Output-1 0 Not editable!
509 Output-2 0 Not editable!
510 Power supply status value 0 Not editable!

SMS Commands and Alerts

Maintenance

Troubleshooting

Deak Solar MobilTherm IP 67
Deak Solar MobilTherm IP 67
Deak Solar MobilTherm IP 67
Deak Solar MobilTherm IP 67
Deak Solar MobilTherm IP 67
Deak Solar MobilTherm IP 67
Deak Solar MobilTherm IP 67
Deak Solar MobilTherm IP 67
Deak Solar MobilTherm IP 67
Deak Solar MobilTherm IP 67
SKU: MobilTherm-2-IP67

MobilTherm-2-IP67

Solar-Soft

Waterproof, GSM-based temperature alarm and high-current remote control module with built-in battery. Ideal for outdoor and industrial environments where remote control and temperature monitoring are required.

Package contents: 1 device with built-in whip antenna and battery + power supply + 2 thermometers with 10m cable.

Our devices operate most reliably on the One network.

In stock
49.990 Ft nettó + 13.497 Ft áfa
63.487 Ft gross
View full details